MMC Combos AR-15 Trigger Upgrade Kit Including Davidson Defense Skeletonized Red Trigger + CMMG Lower Parts Kit + Hogue Beavertail Grip + Davidson Defense Anti Walk Pins

FEATURES:
Light but very safe 3 lbs trigger pull. 
Ultra High Quality Top End Match Trigger System
This single-stage, adjustable, drop-in trigger boasts a solid 3-pound pull weight and is pre-assembled in hard coat Anodized aluminum housing for immediate competition, hunting, and tactical applications right out of the box.
This trigger features a trigger reset aid; when the hammer comes down, it pushes the trigger forward past the reset point, giving you one of the fastest resetting triggers on the market.
Made from American A2 steel, the Trigger, Disconnect, and Hammer designed for ultimate strength and corrosion resistance.
Skeletonized for faster hammer hits and faster cyclic rate.
Wrench size is 5/64

So What  Makes This Trigger Better?

The springs are a vital part of any trigger we use state of the art materials that never loose there spring tension making this trigger be able to have a 3.0 reliable trigger pull where most mfg can only hope for a pull of 3.5 lbs. Davidson Defenses trigger can even ignite the hardest of primers far better than most other brands of drop in triggers. (have you wondered why no one makes AR-15 Triggers below 3.5 LBS  its because they don't want to pay for springs that can do that)

Hand cut hammers sear catch point Davidson Defense hand cuts the hammer so the correct angle and break is always the same on each unit eliminating creep and excessive pull length that many of the other mass mfg trigger mfg have issues with.

Simplistic design you have heard of simple is better and the more moving parts the more friction right?  Davidson Defenses trigger is so simple that the amount of contacting surfaces are minimized  

Computer aided design: See we asked some of the top mechanical engineers at BYU University to fix a trigger that we were making 5 years where it had tons of creep and was almost 4.0 lbs that we more of less copied from another companies design with minor changes What they came back with is wow the look changed little but the hinge & connection points were very much different and specs on the springs were different too it changed everything after a computer worked with even materials and temperature we even were able to simulate what would happen at 1 million rounds fired once we got the specs sourcing the materials and springs were not that easy but over the period of 1 year were able to get the prototype done and then the magic happened it was everything a trigger should be simple fast and reliable.

                                                   -------------------------------------------------------------------------------------------------------------------------------------------------------------

1.     If installing in a receiver that already has a trigger and hammer installed, remove the trigger pin and hammer pin and remove the trigger and hammer as well as the grip, safety selector and detent.  New receivers, install the drop in trigger before mounting the grip.

2.     Insert the trigger pack into the fire control compartment

3.   Insert the hammer and trigger pins. Anti-walk type pins work much better, as standard pins can drop out.

4.     Towards the rear of the trigger cassette you will see two small set screws.  With the trigger and hammer pins in place, turn those set screws down to raise the trigger the point that there is pressure created on the trigger and hammer pins which will hold them in place.  This step is VERY important and will take care of the slight dimensional differences between lower receivers.  

5.   Install the retainers on the anti-walk pins

6.     Insert the safety selector switch.  The hammer needs to be in the cocked position. Take care as it is inserted to not push the selector into the back extension of the trigger.  Replace the safety detent, spring and grip.

7.     At this point you can test the trigger pull and reset. 

Recoil Technologies anti-walk pins are great for drop-in triggers; they replace the original hammer and trigger pins and are retained by special retaining for a positive lock. One side is flared and broached, and the other side is threaded for a screw. Fits small pin lowers (.154"). 

FEATURES:
Made of blackened chrome vanadium tool steel
Corrosion-resistant 
Allen wrench is 1/16th
These are some of the best anti-walk pins on the market.
Retained in the gun, so dirt will not cause a stoppage 
The metal is hard, so there will never be any bending or warping.
Great for drop-in triggers and Mil-Spec triggers.
Works with both forged and billet uppers 
The competitions pins will not work with billet uppers, but ours do. 
Patent-pending design 
This is not anti-rotate; it is anti-walk. That means the pins will not fall out.

INCLUDES: 
One blackened finish stainless steel screw
Pins are .154" diameter, and 1.05" long

These pins replace the original hammer and trigger pins. 

*Note: Screw type may vary

Please note: If the listing says "In-Stock" it means we have all of the items in stock. Please check this LINK to view our most up to date shipping status. 
Warranty, Returns & Terms:
MMC Armory offers a 30 day return, refund and exchange policy. You must email or call MMC Armory and obtain an RMA number prior to any return, refund, or exchange. All returns must include the original order number, receipt or invoice, along with the billing address, shipping address, contact phone numbers, contact emails, and RMA number. Returns, refunds, and exchanges may take up to two weeks, not including transit times, for processing after we receive it. Return shipping costs will be the responsibility of the returning party, with the exception of the wrong item being received or on warranty exchange during the first 30 days after delivery. Items returned for warranty will only be replaced or exchanged, not refunded.