Davidson Defense Silver Fang w/SBA5 Brace 7.5-inch Pistol-Gas 1:7 5.56 NATO AR-15 Tubular Pistol Full Build Kit

Silver Fang w/SBA5 Brace 7.5-inch 5.56 NATO AR-15 Full Build Kit

The Silver Fang is a Full Build Kit built around a Bear Creek Arsenal "Gael" 7.5-inch 5.56 NATO barrel, machined from stainless steel, paired with a "Panhead" billet upper receiver machined in a NOFA configuration with a .458-size ejection port. It pairs a 7-inch MFFAR7 free-float smooth handguard with an AR-15 A2 GI birdcage flash hider at the muzzle, running on a pistol-length gas system. A complete bolt carrier group, Mil-Spec charging handle, complete Lower Parts Kit, carbine buffer-system components, and an SB Tactical SBA5 pistol stabilizing brace round out the rest of the build. The lower receiver is not included, leaving the buyer to select and supply that component separately.

Key Features

• Bear Creek Arsenal "Gael" 7.5-inch 5.56 NATO barrel, 1:7 twist, stainless steel
• Pistol-length gas system with micro low-profile steel gas block
• "Panhead" billet upper receiver, NOFA configuration, .458-size ejection port
• 7-inch MFFAR7 free-float smooth handguard
• AR-15 A2 GI birdcage flash hider
• SB Tactical SBA5 pistol stabilizing brace included
• Complete Mil-Spec Lower Parts Kit and carbine buffer-system components included
• Lower receiver is not included.

Barrel and Gas System

The "Gael" barrel runs 7.5 inches long, chambered in 5.56 NATO and machined from stainless steel. It carries a 1:7 twist rate and a 1/2x28 muzzle thread. Gas cycles back to the action through a pistol-length system, running a pistol-length gas tube and a micro low-profile steel gas block sized to a .750-inch diameter.

Upper Receiver and Handguard

The upper receiver is a "Panhead" billet unit machined in a NOFA configuration, featuring a .458-size ejection port. The ejection port carries a standard .223/5.56 door with its rod and spring installed. Over the barrel sits a 7-inch MFFAR7 handguard, a smooth free-float design.

Muzzle Device

Capping the muzzle is an AR-15 A2 GI birdcage flash hider, threaded to match the barrel's 1/2x28 pattern and secured with the included 1/2-inch black crush washer.

Bolt Carrier Group and Charging Handle

A complete AR-15 bolt carrier group is included, made in the USA and listed for use across 5.56 NATO, .223 Remington, .300 Blackout, and .350 Legend. That broader listing describes the BCG itself; the barrel and chambering on this build remain 5.56 NATO. A Mil-Spec AR-15 M4 charging handle rounds out the upper's operating components.

Lower Parts Kit and Buffer System

A complete Mil-Spec AR-15 Lower Parts Kit covers the fire-control and lower-control internals needed once a lower receiver is on hand. Behind it sits a Mil-Spec heavy-duty six-position buffer tube, holding a standard AR-15 carbine buffer weighing 3 ounces and a standard USA-made recoil spring. An AR-15 carbine castle nut and Mil-Spec AR-15/M16 receiver end plate secure the buffer tube assembly to the lower.

Stabilizing Brace

Capping off the rear of the build is an SB Tactical SBA5 pistol stabilizing brace, finished in black, built for a Mil-Spec buffer tube and matching the buffer tube included with this kit.

Follow all manufacturer instructions and safe handling practices.

Ensure compliance with all applicable federal, state, and local laws.

Lower receiver is not included.